#Navcoder bus simpleinterface2 install
#Navcoder bus simpleinterface2 serial
#Navcoder bus simpleinterface2 software

Will ignition dot turn black when connecting interface to car so that pin1 is also powered? or what is the problem?Д®dit: exactly! it works! i have powered pin 1 of interface and i get both black dots! I have conected interface to 220v/12v ac/dc power adapter (+12v to pin 16 and gnd to pin4+5) but i get the same results

I have modded my vag com kkl interface with ft232BL (not RL) as you said and installed inpa (loader 4.4.7, bmw group rectification programs uk v3.01) but when i connect interface to computer and start inpa (_.ipo) i only get battery on = black dot (ignition is off = white dot)

#Navcoder bus simpleinterface2 software

Now you can use navcoder or other i-bus software You could search in wds for your car wires you will need 12v, gnd, and i-bus wich is usually a white and yellow cable OBD2 connector pin 4 or 5 to negative (gnd) cableДЄnyway just plug it into your obd2 and start navcoder or connect it to your cd changer or radio, whatever. OBD2 connector pin 16 to 12v Positive cable With this in mind, connect three cables as follows The Resler interface works with 4 outputs (ibus, 12v, gnd and NTSC) NTSC signal is used to the camera and as we don't have the chip for its management, just forget about it. It work's with inpa,dis,sss, carsoft 6.1.4 () and navcoder alsoДЇor the navcoder you usually need a RESLER interface but you don't really need it Note: This interface supports cars from 96/98 to March 2007 In case anyone wants to do it in the FT232RL here are the outputs of the chip. Note: if you don't do this circuit you will not be able to do CAR KEY MEMORY So you need to solder pins 17,18 and 20 of the FTDI chip (this applies to the BL and BM) like thisД«ut if we want some REAL battery and ingnition detect, we must do this circuit If your vagcom comes with ft232bm/bl chips, don't worry you only need to do some work We need to invert RI # and DSR # signals to fool the detection of battery and ignition, in order to be able to encode.Д¬heck your I / O Controls settings, them must be like this: Prog 3.5' () to modify the programming of the eeprom FT232RL,

#Navcoder bus simpleinterface2 serial

Now we need to adjust the serial port, press the Windows key and Pause (both), then follow these images (sorry my XP is in spanish language)ДҐ# Download the 'M.

#Navcoder bus simpleinterface2 install

I preferred to catch it on ebay, because it was more comfortable and cheaper than going to catch the pieces out there, also for those wishing to DIY, I leave the chart with specific connections.ДЈ# Open your vagcom and solder obd2 pins 7 and 8, which are the K lines, otherwise you will not be able to access to all modules from the carД¤# If you have buyed vagcom with ftdi 232 rl, for the software mod, you will need this driver 'CDM WHQL certified' (), so unpack it, connect the cable, and install all with this driver. why? well basically because that chip support software mods.Дў# As my 530d do not have odb2 connector, I order a cable adapter from obd2 to 20 pin bmw, ebay seller is ( Car.Doctor ) another 8 ***8364 + shipping. Hi guys, first of all, this isn't new but all info is spread over there and it's a bit difficult to get all info together so i made this postДЎ# buy some Vagcom cable KKL 409.1, just 8 ***8364 + shipping from ebay, ask the seller if it has the chip FT232RL.